|
DECREASE ELECTRICAL
CONSUMPTION BY AS MUCH AS 50% WITH A POWER-SAVE
ENERGY SAVING KIT!
WHY USE A POWER-SAVE ENERGY SAVING KIT?
Power-Save Energy Saving Kits are a cost-effective
way to purchase a combination of Power-Save products! A
Power-Save Energy Saving Kit significantly reduces electric
bills by eliminating wasted electrical consumption and
increasing the overall efficiency of the home. In the event
you decide to 'go solar' down the road, the Power-Save Energy
Saver Kit will allow you to install a much smaller and less
expensive solar system!
Power-Save Energy Saving Kits include:
1. The Power-Save 1200 Energy Saver
The Power-Save 1200™ is a small gray box that fits neatly
next to your breaker panel, saves you money year after year and
protects the entire home.
The Power-Save 1200™ was designed with the homeowner in
mind, providing lower energy bills, increased motor and
appliance life, for all of the equipment inside of your
house.
Residential customers throughout North America could see a
realized savings of 8% - 10% typically and as much as 25% on
their electrical usage (and thus power bills).
The Power-Save 1200™ is UL Certified as
the Cat. No. ABET 2201 and CSA certified.
2. The Power-Save Solar Attic Fan
Saving energy in your home must start at the top. As warm air
rises, it collects in the attic making your entire house hotter
and your air conditioning less efficient. This costs you
valuable dollars and unnecessary wear and tear on your cooling
equipment.
The Power-Save Solar Attic fan removes hot air from the attic
keeping your home cooler while maximizing your air conditioner's
efficiency. The solar powered fan draws no electricity from
the utility and will cost you nothing to operate!
Removes Hot Attic Air; Solar Powered; Up to 850 CFM Air Flow;
Optional Thermostat; Same Day installation; Proudly Made in USA;
10/5/25 Year Warranty; Saves Energy
Easy Installation; Watch a 'This Old House' Video Install!
3. Power-Save Radiant Barrier
Radiant barriers are installed in homes—most commonly in
attics—to reduce summer heat gain and winter heat loss, which
helps lower heating and cooling costs. The barriers consist of a
highly reflective material that reflects radiant heat rather
than absorbing it.
How Radiant Barriers Work
Heat travels from a warm area to a cool area by a
combination of conduction, convection, and radiation. Heat flows
by conduction from a hotter material to a colder material when
the two materials touch. Heat transfer by convection occurs when
a liquid or gas is heated, becomes less dense, and rises.
Radiant heat travels in a straight line away from the hot
surface and heats anything solid as the wave of energy hits it.
When the sun heats a roof, it's primarily the sun's radiant
energy that makes the roof hot. A large portion of this heat
travels by conduction through the roofing materials to the attic
side of the roof. The hot roof material then radiates its gained
heat energy into the cooler attic (some of the roof's heat will
radiate in other directions too). A radiant barrier reduces the
radiant heat transfer from the roof to the attic space.
Fiberglass re-enforced (perforated) aluminum foil insulation;
Fire retardant; Reflects 95% of radiation heat Perforated
aluminum foil radiant barrier to eliminating sweating; Use for
attics, roof and walls ; Easily stapled into place in attic on
ceiling joists or rafters, sealed with aluminum tape; Adhesion
Good on clean and dry surface; No Discoloration Resistance
Excellent resistance to water, water vapor, oxidation and
weathering.
4. Power-Save Duct Seal System
Duct sealing is a combination of Power-Save Radiant Barrier and
Power-Save Duct Seal.
Leaky ducts can reduce heating and cooling system efficiency
by as much as 20 percent. Sealing and insulating ducts
increases efficiency, lowers your energy bills, and can often
pay for itself in energy savings.
Plus, if you’re planning to install new heating and cooling
equipment, a well-designed and sealed duct system may allow you
to downsize to a smaller, less costly heating and cooling system
that will provide better dehumidification.
1) Tape all seams in duct work
2) Wrap all duct work with radiant barrier
3) Use same tape to attach radiant barrier to duct work and seal
all seams
Power-Save Energy
Savings Kit - Price includes shipping &
handling
Please Note: 5% Sales Tax added to Maine
orders |
|
